How do I reduce the size of my photo,now 5.4mb so I can post it?

Tony, I am aware that you have recently changed your email details but a friend of mine is still having difficulty contacting you, he would like to purchase one of the ALR inlet manifolds. He is located here in NZ so phone calls would need to be coordinated time wise, can you please advise the best way to deal with this.

I am currently overhauling a set of Bowdenex front brakes which are destined for the sprint car project.  The cables were still connected up to the back plates and operating levers and that end of the system is no problem.  The other end of each cable has a threaded rod attached and between this and the cable outer is a piece of mild steel 1" x 1/4" x 4" long  with three holes. This is presumably bolted to the chassis (front cross-member?) to locate the cable outer.  It looks as if there should be a threaded sleeve that screws onto the end of the cable to clamp it against the piece of steel bar, and take up the slack.
I am going to use a Ruby type brake cross-shaft and would like to know how the two Bowden cables are connected to the central lever of the cross-shaft. I assume there must be some form of balance arrangement. 
My project will have a floor attached to the underside of the chassis cross-members and about 4" of ground clearance so I cannot afford to have any parts of the braking system protruding below the floor.

I found an excellent 36 Page article on the above on mg-cars.org.uk. Sorry haven't done link. It covers all coils and distributors up to the 60's approx. Including DK but not DJ. It's entitled " Overseas Correspondence Course, Section 3 Coil Ignition." It shows among many other things the 3 different cam profiles fitted in dizzies up to that time and the reason for the changes of same over the years.
Happy reading!
Dave.

Help!

With a customer's 1934 RP soon to go home, we've just found that one of the window winder springs is broken.  It's from the offside, although I'm pretty certain that they're reversible.

Does anyone have one that they'd part with?

Thanks!

Martin.

Attached Files

Thumbnail(s)
   

Currently contemplating getting a car lift like the EZ car lift or Quickjack. Has anybody any thoughts or experience with these type of lifts and are they suitable for a 7 (Cambridge)?
Simon

Hi All,

My Ulster Rep has wedge shaped boxes under the seat cushions, angled downward at the rear. The question I have is if this is the sort of thing the original cars had, or if the cushions were merely dropped on the floor to give the lowest seating position.

Feeling Autumn in Seattle

Erich

THE ‘UFFINDEL’ 1928 AUSTIN 7 SPECIAL
The first car to cross the start line at the first Australian Grand Prix at Bathurst
Held in current ownership for 54 years
Chassis No: Not specified
Engine No: M63288
The legendary Austin 7 has competed in almost every discipline of motorsport since its inception in 1920 when a young Herbert Austin conceived a small car to meet the needs of young families. The ideas were spurred by the Horsepower tax of the day and was quite a departure from the Swift of Coventry earlier conservative vehicles.  As the company was in dire financial straits. Austin employed the services of 18-year-old draughtsman, Stanley Edge, from the Austin factory at Longbridge, Birmingham to aid in the drawing of detailed plans.
Austin’s son-in-law Arthur Waite, who became a legendary Austin 7 racing driver, began his career with remarkable sporting successes at Brooklands in March 1923 followed at Monza. Notwithstanding the unavoidable run of failures that any racing marque had to endure to find perfection, Waite and Lou Kings (chief tester) persevered. He went on to establish Austin Distributors in Melbourne.  Gordon England also established six new class records at Brooklands in his special lightweight 2-seater body weighing just 20 lb (9.1 kg) and entered the 1100 cc class for the Junior Car Club 200-mile race at Brooklands in October 1923 finishing in second place and breaking five class records. These milestones saw the birth of the Austin 7 racing legend that has thrilled spectators and challenged competitors for almost 100 years.
This intrinsically important racing car with Australian Grand Prix provenance for sale at Motorclassica was built into an aluminium bodied racing car in about 1934 by the South Australian, Ron “the Wizard” Uffindell. Referred to as “the Wizard” for his amazing turning ability, his spectacular trail-blazing is well recorded in Australian Grand Prix motor racing history. He started racing at the Centennial Grand Prix in 1936 which was run on the public roads between Victor Harbor and Port Elliot over 250 miles. Uffindel finished this race in 7th place outright having wisely fitted heavier crankshaft and rods in anticipation of the demands on the car. (Retrospectively, this race became known as the 1937 Australian Grand Prix). The following year on the 18 April the Australian Grand Prix was held at Bathurst on unsealed roads. Uffindell drove his little racer from his home town of Adelaide to Bathurst. The ‘Uffindel’ holds the illustrious honour of being the first car to leave the starting line on handicap against Peter Whitehead’s ERA at Mt Panorama at the first Australian Grand Prix held at that circuit. To ensure he would make the distance without refuelling, Uffindel installed a 7-gallon tank and finished in an astonishing 8th place. Ron Uffindell was a small man in stature at about five feet 5 inches tall. The image of him hanging onto the steering wheel of this little car, flat strap down Conrod Straight on a dirt road at 68 mph while being overtaken by a supercharged K3 Magnette at 105 mph is legendary in the annals of Australian motorsport. He then drove the little Austin 7 back to Adelaide via Melbourne and Mt Gambier along the Great Ocean Road!
In 1939, the Austin 7 was first outright in the South Australian Junior Grand Prix run at Lobethal establishing an average speed of just over 68 mph. Other competition achievements include the Australian Hill Climb Championship at Rob Roy winning the 850cc class. Once again, Ron Uffindel drove to and from the event.
An early member of the Sporting Car Club of SA. Ron Uffindel owned this car for 19 years before selling it to Gordon Walker who continued competing in SCCSA club events. The car has had only 4 owners since Ron Uffindel including Australian Sports Car Champion, Phil Moore. In its current 54-year ownership it has made guest appearances at both the Lobethal re-enactment events in 2008 and 2009 driven by Geoff Redin and Ral Rainsford. The car was honoured for its historical Australian Grand Prix and South Australian motoring significance by being the first car flagged off the starting line in 2008 by highly respected Australian motorsport flagman, Glen Dix. It has also run at the Winton Historics in 2010.
The ‘Uffindell’ offers a superb opportunity to acquire an Austin 7 with unequalled Australian racing provenance held in its current custodianship for 64 years. Its acquisition offers a rare and desirable opportunity for a discerning collector of Australian Grand Prix history. The car is accompanied by a tonneau which zips down the middle; the 4 original mudguards made by Ron Uffindell; an original poster of the 1939 Lobethal races and a CD including significant historical photographs of the car racing in the early days and at the Lobethal re-enactment event in 2008 and 2009. Ron Uffindel’s historic race records are held in safe keeping within the Austin 7 Club of South Australia archives.

https://www.mossgreen.com.au/m/lot-detai...-7-SPECIAL

Could someone please suggest what chemical cleaner I could use to clean Zenith carb bodies?

Hi,
I wonder if anyone can help with some pictures as to the best way, and in fact how, to set up an external oil filter on a 1927 coil engine. I need to know where is best to set up the pipework running into the filter and if there are any modifications needed to the engine to achieve it. Rubber, copper piping or braided? Any modification to the oil pump? 
Any help would be most grateful. 
Thanks in advance.
Tim