The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
PCD Wheel studs

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
PCD Wheel studs
Duncan Grimmond Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 1,977 Threads: 90
Reputation: 17
Location: Ripon
#1
29-11-2017, 02:03 PM (This post was last modified: 29-11-2017, 02:04 PM by Duncan Grimmond.)
Could someone post the PCD for wheel studs please?
Or, tell me where to find it?
Reply
Peter Clayton Offline
Member
***
Joined: Aug 2017 Posts: 220 Threads: 19
Reputation: 1
#2
29-11-2017, 02:44 PM
www.ptsintl.com/pdfs/Multihead%20Centinel/PitchCircle.pdf How good are your maths.?
Reply
Duncan Grimmond Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 1,977 Threads: 90
Reputation: 17
Location: Ripon
#3
29-11-2017, 03:46 PM (This post was last modified: 29-11-2017, 03:48 PM by Duncan Grimmond.)
Thanks for that, I wanted to check my calculation against the reality of a factory drawing. It's really difficult finding the exact centre point of the stud...or am I disappearing up my own fundament?
Reply
AustinWood Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 984 Threads: 6
Reputation: 12
Location: Scottish Borders
#4
29-11-2017, 05:24 PM
It's usually easier to measure the spacing from the side of the stud than trying to guess the centre. That is left side to left side or right side to right side which will be the same as centre to centre.
I make the stud spacing 4" measuring the holes on a hub outer
Jim
Reply
Marcus Ling Online
Member
***
Joined: Aug 2017 Posts: 102 Threads: 10
Reputation: 0
#5
29-11-2017, 09:23 PM
(29-11-2017, 02:03 PM)Duncan Grimmond Wrote: Could someone post the PCD for wheel studs please?
Or, tell me where to find it?

Hi Duncan,

I believe the PCD is 4 and 5/8, that what it is on the hub holding tool I make here.

Cheers

Marcus
Reply
Paul N-M Offline
Member
***
Joined: Aug 2017 Posts: 226 Threads: 9
Reputation: 5
Location: Edinburgh/Lothians
Car type: Seven Special
#6
30-11-2017, 04:34 PM
(29-11-2017, 02:03 PM)Duncan Grimmond Wrote: Could someone post the PCD for wheel studs please?
Or, tell me where to find it?

4 and 5/8" is correct.

Paul N-M
http://www.vintageandclassicworckshops.com
Reply
Duncan Grimmond Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 1,977 Threads: 90
Reputation: 17
Location: Ripon
#7
30-11-2017, 06:55 PM
(30-11-2017, 04:34 PM)Paul N-M Wrote:
(29-11-2017, 02:03 PM)Duncan Grimmond Wrote: Could someone post the PCD for wheel studs please?
Or, tell me where to find it?

4 and 5/8" is correct.

Paul N-M

Many thanks.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)