The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
Top Tips

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Top Tips
Ray White Offline
Austin Swallow nut
****
Joined: Aug 2017 Posts: 294 Threads: 11
Reputation: 3
#11
06-05-2018, 11:42 PM (This post was last modified: 06-05-2018, 11:43 PM by Ray White.)
Make sure the rear axle tapers are tight. I suspect there are many A7s rattling around on their key ways with a view to a broken half shaft.
Reply
Colin Morgan Offline
Member
*****
Joined: Aug 2017 Posts: 1,050 Threads: 108
Reputation: 3
Location: Cheshire
#12
07-05-2018, 04:34 PM
If you come across woodworm and treat it, put a pencil circle round each hole - then you can see if there is any fresh activity next time you look.  The blighters can continue to emerge for some years - in the summer - and if two get together and lay eggs, then there could be a lot more trouble...

Colin
Reply
Tony Press Offline
Older Member
*****
Joined: Aug 2017 Posts: 1,746 Threads: 42
Reputation: 15
Location: Malvern, Victoria, Australia
#13
07-05-2018, 11:35 PM
(06-05-2018, 07:32 PM)Dave Wortley Wrote: True Ian they are quite weak. I have my own torque wrench ie. losing arm strength through getting old and weedy.
Cheers,
Dave.

And using the standard Austin Seven Wheel Brace should limit the torque!

Cheers, Tony.
http://austin7club.org
Reply
Mike Costigan Offline
former 'Grey Mag' editor
*******
Joined: Aug 2017 Posts: 3,014 Threads: 169
Reputation: 37
Location: Sherwood Forest
Car type: 1938 Talbot Ten Airline
#14
08-05-2018, 08:32 AM
Newcomers to an Austin Seven can be alarmed at the lack of pressure shown on the oil gauge! As a general rule-of-thumb, once the engine is fully warmed through - and that can easily be five to ten miles running - approximately 1psi per ten mph is about right (on a 2-bearing engine, perhaps slightly less, on a three-bearing engine maybe a bit more).
Reply
Colin Morgan Offline
Member
*****
Joined: Aug 2017 Posts: 1,050 Threads: 108
Reputation: 3
Location: Cheshire
#15
08-05-2018, 09:21 AM
Yes, it can be alarming the first time stopped at traffic lights once the engine has thoroughly warmed up - with almost no pressure showing.  This is in stark contrast to start-up, when the pressure shoots off-scale and should stay there a while.  

Colin
Reply
Robert Leigh Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 926 Threads: 22
Reputation: 10
Location: Near Cambridge, UK
Car type: 1928 tourer (mag type), short chassis Gould Ulster
#16
08-05-2018, 10:20 AM
(07-05-2018, 04:34 PM)Colin Morgan Wrote: If you come across woodworm and treat it, put a pencil circle round each hole - then you can see if there is any fresh activity next time you look.  The blighters can continue to emerge for some years - in the summer - and if two get together and lay eggs, then there could be a lot more trouble...

Colin
I like to plug old woodworm holes with boot polish; then any new holes show very easily.
Robert Leigh
Reply
Colin Morgan Offline
Member
*****
Joined: Aug 2017 Posts: 1,050 Threads: 108
Reputation: 3
Location: Cheshire
#17
08-05-2018, 04:55 PM
Do others use a standard wooden clothes peg to hold out the choke?  (This tip came from Jim Young of the PWA7C even before I had put my car on the road.)  The spring is a bit strong, so I have always use two - they look older than the car after years of use.  Not sure if they are available any more in this time of plastic - do any of the cherished suppliers carry them?
Reply
Viteran Offline
Member
***
Joined: Dec 2017 Posts: 100 Threads: 16
Reputation: 1
Location: South yorkshire
#18
08-05-2018, 05:29 PM
I thought everyone did, I assumed the peg was part of the original kit !
Reply
Colin Wilks Offline
Senior Member
****
Joined: Nov 2017 Posts: 562 Threads: 56
Reputation: 7
Location: West Yorkshire
Car type: Type 65 1934 + RP 1932
#19
08-05-2018, 07:01 PM
(08-05-2018, 04:55 PM)Colin Morgan Wrote: Do others use a standard wooden clothes peg to hold out the choke?  (This tip came from Jim Young of the PWA7C even before I had put my car on the road.)  The spring is a bit strong, so I have always use two - they look older than the car after years of use.  Not sure if they are available any more in this time of plastic - do any of the cherished suppliers carry them?

Not sure about the choke as I've only managed to get my car round the block so far, but I can confirm a standard wooden clothes peg is ideal for holding the cam followers clear when removing or installing the camshaft (with thanks to Ian Bancroft for the tip).
Reply
Austin Carr Offline
Member
***
Joined: Aug 2017 Posts: 193 Threads: 11
Reputation: 0
Location: Oxfordshire
#20
08-05-2018, 07:02 PM
(08-05-2018, 04:55 PM)Colin Morgan Wrote: Not sure if they are available any more in this time of plastic - do any of the cherished suppliers carry them?

I don't about cherished suppliers but wooden ones are available at Tesco and other supermarkets:-

https://www.tesco.com/groceries/en-GB/pr.../273772520
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)