Joined: Aug 2017 Posts: 741 Threads: 8
Reputation:
11
Location: N W Kent
As per the thread title, has anybody on here had a honeycomb rad re cored? if so, could you share who did the work -there doesn't seem to be an abundance of people doing this -any guidance on the whether I'm going to need to sell a kidney to get the rad looking right would be good too. This isn't actually for one of my A7s, it's for another 20's car i have, the rad core is about the same size as that on an Austin 20.
Thanks in anticipation for any replies, Stuart.
Joined: Aug 2017 Posts: 1,808 Threads: 99
Reputation:
21
Hi stuart,
I had 3 austin 7 honeycomb rads done by Tony welder.
Sadly missed the cut off for £325.00 aparently the manufacturers now know it's being used in vintage cars.
Had to pay £425.00 each 2 to 3 years ago.
He may charge more know.
Done an excellent job though, highly recommended.
Tony.
Joined: Aug 2017 Posts: 881 Threads: 48
Reputation:
4
Location: North Wiltshire
Car type: 1927 Chummy, 1938 Big Seven 1/2 a Trials Chummy
Lots of radiator repair men can fit the honeycombe core but very few people make them. Most repairers get the core, made to size from Vintage Wings and Radiators in Manchester (you can Google for the address) and then fit them. They are not cheap though.....
Joined: Mar 2018 Posts: 694 Threads: 33
Reputation:
3
Location: Lot region FRANCE
I cheated, modern core with a grille of honeycomb in front of it (all integral with the rad) You get the benefit of better cooling and looks like the original. Much cheaper than proper honeycomb, but if you are a purist, it wouldn't suit!
Joined: Mar 2015 Posts: 5,441 Threads: 231
Reputation:
67
Location: Scotchland
Tony Wilder has now retired - so I understand. Sad news as the rad work (including honeycomb) he did for me over the years was fantastic.
Joined: Aug 2017 Posts: 1,808 Threads: 99
Reputation:
21
That's sad news for the austin seven and MG world.
Tony was by far the cheapest I knew.
Stuart, it looks like you may have to get a valuation on that kidney.
Tony.
Joined: Aug 2017 Posts: 1,230 Threads: 33
Reputation:
7
Location: Salop
Car type: '28 GE Cup. '28 AD Chummy '30 RL Saloon. '34 RP Saloon. Too Many toys!
Not wishing to get too anal. But I had understood honeycomb core was only used for a short period in late 1929 or early 1930. My interest was sparked by such a rad I have in my chummy. Most of the cars earlier and later had a Serk pattern A (from memory). Basically a wiggly vertical zig zag seperated by a gap. Also availible from the same source noted above.
When I did my saloon some years ago I had a modern core fitted, but set back sufficiently to later fit a 6mm thick honeycomb dummy in front, which I recall I stuck on with Tigerseal.
It looks good, but the modern core doesnt hold so much water as a pukka vintage core and thus the car does boil when driven like I was tought when 3 up - "Never take your foot off the throttle, and if you do, never, ever use the brake"
Joined: Jan 2019 Posts: 127 Threads: 8
Reputation:
0
I have used Anglia Radiators in Cambridge several times and found thieir work to be excellent.
Joined: Aug 2017 Posts: 119 Threads: 8
Reputation:
1
When I bought a new core for the cup model, the cost was the same for an a-type or honeycomb core. 5 years ago, the cost was £300+ vat for the core alone. I fitted it myself.
Peter
