The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
3rd brush ?

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
3rd brush ?
Tiger Offline
Senior Member
****
Joined: Apr 2018 Posts: 507 Threads: 129
Reputation: 2
Location: Staffordshire
Car type: Ruby mk 2
#1
31-01-2019, 01:32 PM
Hello people
Can anyone advise which way to rotate the 3rd brush to adjust the charge.
Regards
          Tim
PS can you get to adjust after fitting the Dynamo
Reply
Nick Salmon Offline
Older, but none the wiser...
*****
Joined: Aug 2017 Posts: 1,347 Threads: 241
Reputation: 23
Location: North Herts
#2
31-01-2019, 02:31 PM
There is a circular band of spring steel, around the body of the dynamo, that is secured by a screw and shaped nut. Remove it. Looking at the rear of the dynamo (i.e. the end nearest you, from which you removed the band, the third brush moves anti clockwise to increase, clockwise to decrease. Move it about an 1/8th of an inch at a time, start the engine to check output on ammeter. Stop the engine and move it again if necessary etc etc.
Reply
fatcatvera Offline
Member
***
Joined: Jun 2018 Posts: 65 Threads: 14
Reputation: 0
Location: Kenilworth, Warwickshire
#3
31-01-2019, 02:59 PM
What should the target charge current be? My Ruby sits at about 2A max with higher engine speeds.
Reply
Reckless Rat Offline
Resident Frog
*****
Joined: Aug 2017 Posts: 2,400 Threads: 33
Reputation: 36
Location: Deepest Frogland 30960
Car type: 1933 RP Standard Saloon
#4
31-01-2019, 03:13 PM (This post was last modified: 31-01-2019, 03:14 PM by Reckless Rat.)
About 8 amps max with no lights or brake lights on. Any more and you'll boil the battery dry and damage the dynamo. Summer charge rate should be about 1-2 amp.
Reply
AustinWood Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 985 Threads: 6
Reputation: 12
Location: Scottish Borders
#5
31-01-2019, 04:01 PM
The third brush is the one on the right viewed from above, underneath the dynamo casing and is a bit fiddly to reach. It is held by a screw in the end of the dynamo on the right which needs to be slackened.
I have LED lights and have it set to show 4 Amps max on the ammeter.
Jim
Reply
Tiger Offline
Senior Member
****
Joined: Apr 2018 Posts: 507 Threads: 129
Reputation: 2
Location: Staffordshire
Car type: Ruby mk 2
#6
31-01-2019, 05:03 PM
Many thanks for the replies
Just what I needed.
Any details on the LEDs would be good.
Regards
Tim
Reply
AustinWood Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 985 Threads: 6
Reputation: 12
Location: Scottish Borders
#7
31-01-2019, 07:41 PM
I got my LEDs here:
http://www.dynamoregulatorconversions.com/
Jim
Reply
David.H Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 849 Threads: 123
Reputation: 1
#8
31-01-2019, 08:34 PM
A bit off topic sorry! 
Do you need to do anything special to put in an LED bulb? If I remember from putting LED bike flashers on my Magnette there were some problems with earth. ......?.
Reply
Reckless Rat Offline
Resident Frog
*****
Joined: Aug 2017 Posts: 2,400 Threads: 33
Reputation: 36
Location: Deepest Frogland 30960
Car type: 1933 RP Standard Saloon
#9
31-01-2019, 08:40 PM
Just a good earth, and make sure they are connected the correct way round!
Reply
Bob Culver Offline
dogged member, NZ
*****
Joined: Aug 2017 Posts: 2,748 Threads: 31
Reputation: 95
Location: Auckland, NZ
#10
31-01-2019, 10:29 PM
As this will come up on Search, the 3rd brush described is for the early 4 pole dynamos. 
On the 35A and 35M as fitted originally after about 1932 the 3rd brush is middle brush at top  and is not rigidly clamped.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)