The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
Starter Grommet

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Starter Grommet
williamsderbys Offline
Junior Member
**
Joined: Aug 2017 Posts: 37 Threads: 22
Reputation: 0
#1
05-10-2018, 07:35 PM
Does anyone have a suggestion for a grommet carrying the cable through the casting on a bacon slicer starter?
It looks a lot like the black one on old electric irons as it has an extended body.
I have made a wooden pattern but lack the skills to cast one in rubber.
J.W
Reply
Chris Garner Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 967 Threads: 117
Reputation: 3
Location: Melton Mowbray.
#2
05-10-2018, 07:56 PM
   
I'm not sure whether the grommet in question is BD94 or 126.
Reply
williamsderbys Offline
Junior Member
**
Joined: Aug 2017 Posts: 37 Threads: 22
Reputation: 0
#3
06-10-2018, 05:35 PM
(05-10-2018, 07:56 PM)Chris Garner Wrote: I'm not sure whether the grommet in question is BD94 or 126.

Chris - I think it must be BD 94 as it refers to starter switch cables and says 3. (July 28 parts list page 17)
I suppose the other 2 would be for the 'progress' of the cables from battery to starter.
Perhaps thinking of getting some made but assume someone would want to make a lot and demand would be for say 10 at the most!
John W
Reply
Austin Carr Offline
Member
***
Joined: Aug 2017 Posts: 193 Threads: 11
Reputation: 0
Location: Oxfordshire
#4
06-10-2018, 06:45 PM
Chris, Could you make the grommet from a piece of rubber hose and an "0" ring?
Reply
Robert Foreman Offline
Precision Engineer
****
Joined: Aug 2017 Posts: 557 Threads: 89
Reputation: 7
Location: Deepest darkest Kent
#5
06-10-2018, 07:33 PM
What about one of these and just cut the end off?
Reply
daveg Offline
Member
***
Joined: Aug 2017 Posts: 98 Threads: 3
Reputation: 0
#6
06-10-2018, 08:10 PM (This post was last modified: 06-10-2018, 08:24 PM by daveg.)
If it is BD94 you require this is looks quite close:- 

https://www.ebay.co.uk/itm/15-Pcs-Rubber...0505.m3226

It is for a hole diameter of 14 mm as opposed to 17/32" (13.5 mm). If it doesn't fit as is you should be able to cut a small bit out and re-glue it.

If you search for strain relief or sleeve grommet or cable sleeve you may find other possibilities.

Edit - Just noticed the long delivery on the above item. This one for a 13mm hole may be better:-

https://www.ebay.co.uk/itm/Rubber-Strain...5Hmr1fP57A
Reply


Forum Jump:


Users browsing this thread: 3 Guest(s)