The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
Pressure Fed Conversion

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linear Mode
Pressure Fed Conversion
Terrytuned Offline
Senior Member
****
Joined: Aug 2017 Posts: 327 Threads: 1
Reputation: 19
Location: Bristol
#24
24-02-2023, 11:37 AM
Russel side clearance of 10-12 thou on pressure fed 12-14 on splash rods, if you have your oil pressure relief valve set at 65psi oil warm there is no need for any extra clearance. your nose feed bolt should have a 1/4"/6.5mm cross feed hole and at least the same size bore some were smaller restricking the feed. Terry.
Reply


Messages In This Thread
Pressure Fed Conversion - by Charles P - 18-02-2019, 03:15 PM
RE: Pressure Fed Conversion - by Robert Leigh - 18-02-2019, 04:20 PM
RE: Pressure Fed Conversion - by Chris KC - 18-02-2019, 05:21 PM
RE: Pressure Fed Conversion - by jansens - 18-02-2019, 05:42 PM
RE: Pressure Fed Conversion - by Charles P - 18-02-2019, 06:02 PM
RE: Pressure Fed Conversion - by Chris KC - 18-02-2019, 07:10 PM
RE: Pressure Fed Conversion - by Robert Leigh - 18-02-2019, 07:18 PM
RE: Pressure Fed Conversion - by Chris KC - 18-02-2019, 07:24 PM
RE: Pressure Fed Conversion - by dickie65 - 18-02-2019, 07:53 PM
RE: Pressure Fed Conversion - by Steve Jones - 18-02-2019, 07:57 PM
RE: Pressure Fed Conversion - by Chris KC - 18-02-2019, 08:02 PM
RE: Pressure Fed Conversion - by Charles P - 18-02-2019, 08:48 PM
RE: Pressure Fed Conversion - by dickie65 - 18-02-2019, 09:26 PM
RE: Pressure Fed Conversion - by stuartu - 18-02-2019, 09:59 PM
RE: Pressure Fed Conversion - by dickie65 - 18-02-2019, 10:26 PM
RE: Pressure Fed Conversion - by jansens - 18-02-2019, 10:34 PM
RE: Pressure Fed Conversion - by Charles P - 18-02-2019, 11:23 PM
RE: Pressure Fed Conversion - by Chris KC - 18-02-2019, 11:42 PM
RE: Pressure Fed Conversion - by squeak - 15-02-2023, 02:52 PM
RE: Pressure Fed Conversion - by Terrytuned - 16-02-2023, 12:41 PM
RE: Pressure Fed Conversion - by squeak - 17-02-2023, 12:33 AM
RE: Pressure Fed Conversion - by dickie65 - 23-02-2023, 07:26 PM
RE: Pressure Fed Conversion - by squeak - 24-02-2023, 02:20 AM
RE: Pressure Fed Conversion - by Terrytuned - 24-02-2023, 11:37 AM
RE: Pressure Fed Conversion - by squeak - 24-02-2023, 12:54 PM

Forum Jump:


Users browsing this thread: 2 Guest(s)