The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
Early rear axle shims

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Early rear axle shims
Marcus Ling Offline
Member
***
Joined: Aug 2017 Posts: 102 Threads: 10
Reputation: 0
#1
14-12-2023, 05:34 AM
Hi,
Can anyone suggest if the shims for the crown wheel carrier bearings are available for the early rear axle that doesn't have the adjusters please. 
I have searched the usual suppliers but cant find any listed.

Thanks
Marcus
Reply
Charles P Offline
Eternal Repairer
*****
Joined: Aug 2017 Posts: 1,539 Threads: 61
Reputation: 20
#2
14-12-2023, 06:34 PM (This post was last modified: 14-12-2023, 06:34 PM by Charles P.)
I ended up making shims for my later axle. Not that difficult with a Ruby bearing housing, tin snips and a close fitting parallel punch. I think the torque tube bolt pattern is the same as the earlier axles.
A 1 gallon thinners can, a beer can and a Red Bull can are useful raw materials of different thicknesses.
Reply
Alan Offline
Legend
*****
Joined: Aug 2017 Posts: 1,341 Threads: 34
Reputation: 30
Location: Cheshire
Car type: Race Ulster, 1926 Special, 1927 Chummy, 1930 Box
#3
14-12-2023, 07:00 PM
There’s a company called Springmasters in Redditch. They sold me some shim washers a few years ago.
Alan Fairless
Reply
Chris KC Offline
GO 6285
*****
Joined: Aug 2017 Posts: 3,417 Threads: 107
Reputation: 28
Location: Darkest Bedfordshire
#4
14-12-2023, 07:00 PM
...or if you're the fussy type, it's fairly easy to find sheets / packs of shim steel on eBay...
Reply
Colin Morgan Offline
Member
*****
Joined: Aug 2017 Posts: 1,057 Threads: 108
Reputation: 3
Location: Cheshire
#5
14-12-2023, 07:02 PM
Ten years ago, when I did my '28 Chummy axle, I made a few from 5 thou shim material - 2" OD with a 1 1/2" hole.

Both the OD and hole were punched out.
Reply
Marcus Ling Offline
Member
***
Joined: Aug 2017 Posts: 102 Threads: 10
Reputation: 0
#6
14-12-2023, 10:47 PM
Hi,
Thanks for all the suggestions, I will get on and make some.

Cheers

Marcus
Reply
Charles P Offline
Eternal Repairer
*****
Joined: Aug 2017 Posts: 1,539 Threads: 61
Reputation: 20
#7
15-12-2023, 12:26 AM (This post was last modified: 15-12-2023, 12:28 AM by Charles P.)
My punch approach

   
Reply
Marcus Ling Offline
Member
***
Joined: Aug 2017 Posts: 102 Threads: 10
Reputation: 0
#8
12-01-2024, 01:36 AM
Hi Everyone,

I found some stainless shims on Ebay, that are 50mm OD x 40mm ID and 0.001 thou thick. 10 shims delivered cost me NZD 9.58 or around five quid.

   

Maybe this will help someone in future

Cheers

Marcus
Reply


Forum Jump:


Users browsing this thread: 3 Guest(s)