The following warnings occurred:
Warning [2] Undefined variable $search_thread - Line: 60 - File: showthread.php(1617) : eval()'d code PHP 8.1.31 (Linux)
File Line Function
/inc/class_error.php 153 errorHandler->error
/showthread.php(1617) : eval()'d code 60 errorHandler->error_callback
/showthread.php 1617 eval



Austinsevenfriends › Austin Seven Friends Forum › Forum chat... v
What have you done today with your Austin Seven

Thread Rating:
  • 28 Vote(s) - 3.32 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
What have you done today with your Austin Seven
"Slack Alice" Simon Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 782 Threads: 26
Reputation: 8
Location: On a hill in Wiltshire
#2,741
15-04-2021, 01:23 PM (This post was last modified: 15-04-2021, 01:24 PM by "Slack Alice" Simon.)
First drive in about 5 months.

With two small boys.  We showed them "Beethoven" (the film) in which the final rescue is performed by the children of the house, driving the family car into the inside of a factory.

"We could do that in Grandpa's car..."

So: up and down the road with the 8 year old, and then the 6 year old steering.

Unlike the film, we stopped before we went through the closed garage doors.



I love the dual control aspects of the earlier Austins.
Reply
Malcolm Parker Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 919 Threads: 18
Reputation: 13
Location: North Yorkshire
#2,742
15-04-2021, 03:40 PM
   
Had the Austins out for some fresh air and a chance to sweep up the garage floor.  The RL had a good run out yesterday of about 50 miles, it went so well I thought someone had put the Ulster engine in it over winter.   The Pytchley wasn't too happy last time out and I didn't like the noise the engine was making.   Today I decided to change the distributor and found that the coil end of the HT lead had disintegrated.  I put an old Skoda distributor on and the engine is running nicely.   The Ulster fired up immediately after a six month lay up.
Reply
Bob Culver Offline
dogged member, NZ
*****
Joined: Aug 2017 Posts: 2,748 Threads: 31
Reputation: 95
Location: Auckland, NZ
#2,743
15-04-2021, 08:28 PM
In response to Dave Mann above, decades ago a work colleague reported that fitting a trailer had burned out the hyd switch. i had a simialr car so fitted a relay and OK ever after.
Reply
Malcolm Parker Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 919 Threads: 18
Reputation: 13
Location: North Yorkshire
#2,744
16-04-2021, 03:29 PM
        Today it was time to give the single seater a breath of fresh air, in preparation for taking it down to Boroughbridge where a man will be able to clothe the front with a sleek bonnet and streamlined nose (hopefully without the trademark mouchtache!)
Making sure that there are no loose nuts and bolts or spanners etc lying around on the undertray.
Reply
Nick Salmon Online
Older, but none the wiser...
*****
Joined: Aug 2017 Posts: 1,347 Threads: 241
Reputation: 23
Location: North Herts
#2,745
16-04-2021, 07:20 PM
Malcolm - I presume it will be having its nuts removed as well? (Oops, sorry, too much exposure to The Yorkshire Vet...[Image: wink.png]!)
Reply
Steve Jones Online
Pass the hammer
*****
Joined: Aug 2017 Posts: 1,462 Threads: 26
Reputation: 17
Location: North Yorkshire
#2,746
16-04-2021, 07:49 PM (This post was last modified: 16-04-2021, 07:55 PM by Steve Jones.)
It's taken him a long time to put all the nuts in place, Nick, so removal will not be an option!

In my case, I've been finalising the fitting of a carburettor upgrade to my Ulster before its first event of 2021 in two weeks time. However, my suspicions of a slight head gasket blow were confirmed last thing when I found a cylinder head stud pulling out. Head off tomorrow, Helicoil, new head gasket and re-assembly. Times like these I'm pleased we have SV engines.

Steve
Reply
Steve Jones Online
Pass the hammer
*****
Joined: Aug 2017 Posts: 1,462 Threads: 26
Reputation: 17
Location: North Yorkshire
#2,747
17-04-2021, 05:48 PM
All done and engine back running. Now in the torqueing down process. Gave me something to do whilst the rest of the population were watching a funeral.

Steve
Reply
Duncan Grimmond Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 1,977 Threads: 90
Reputation: 17
Location: Ripon
#2,748
18-04-2021, 10:57 AM
Has somebody died? Who knew...?
Reply
Steve Jones Online
Pass the hammer
*****
Joined: Aug 2017 Posts: 1,462 Threads: 26
Reputation: 17
Location: North Yorkshire
#2,749
18-04-2021, 11:34 AM
(18-04-2021, 10:57 AM)Duncan Grimmond Wrote: Has somebody died? Who knew...?

Apparently, Duncan. You'd have thought there might have been something in the news about it wouldn't you Rolleyes

Steve
Reply
Duncan Grimmond Offline
Posting Freak
*****
Joined: Aug 2017 Posts: 1,977 Threads: 90
Reputation: 17
Location: Ripon
#2,750
Big Grin  18-04-2021, 03:45 PM
(16-04-2021, 03:29 PM)Malcolm Parker Wrote: Today it was time to give the single seater a breath of fresh air, in preparation for taking it down to Boroughbridge where a man will be able to clothe the front with a sleek bonnet and streamlined nose (hopefully without the trademark mouchtache!)
Making sure that there are no loose nuts and bolts or spanners etc lying around on the undertray.

Wot, no moustache? can't be done I'm afraid![Image: biggrin.png]
Reply


Forum Jump:


Users browsing this thread: 66 Guest(s)